Half Yearly Report and Accounts
Released
Released
Announcement PDF
VENTNOR RESOURCES LIMITED
ABN 59 142 014 873
INTERIM FINANCIAL REPORT
FOR HALF-YEAR ENDED
31 DECEMBER 2017
CORPORATE DIRECTORY
DIRECTORS
Paul Boyatzis (Non-Executive Chairman)
Bruce Maluish (Managing Director)
Peter Pawlowitsch (Non-Executive Director)
SECRETARY
John Geary
REGISTERED AND PRINCIPAL OFFICE
Level 1, 6 Thelma Street
West Perth WA 6005
Telephone: (08) 9226 3780
Facsimile: (08) 9226 3764
SHARE REGISTRY
Computershare Investor Services Pty Ltd
Level 11, 172 St George's Terrace
Perth WA 6000
Telephone: (08) 9323 2000
Facsimile: (08) 9323 2033
AUDITORS
RSM Australia Partners
Level 32, Exchange Tower
2 The Esplanade
Perth WA 6000
AUSTRALIAN SECURITIES EXCHANGE
Ventnor Resources Limited shares (VRX) are listed
on the Australian Securities Exchange
Ventnor Resources Limited
1
DIRECTORS’ REPORT
Your directors submit the financial report of the consolidated entity for the half-year ended 31 December
2017. In order to comply with the provisions of the Corporations Act 2001, the directors report as follows:
DIRECTORS
The names of the Directors who held office during or since the end of the half-year and until the date of
this report are noted below. Directors were in office for this entire period unless otherwise stated:
Paul Boyatzis (Non-Executive Chairman)
Bruce Maluish (Managing Director)
Peter Pawlowitsch (Non-Executive Director)
PRINCIPAL ACTIVITIES
The principal continuing activities during the half-year of entities within the consolidated entity was
mineral exploration.
REVIEW OF OPERATIONS
The net loss for the half-year attributable to members of Ventnor Resources Limited was $919,872
(2016: loss of $559,353).
During the half-year ended 31 December 2017, Ventnor Resources Limited (Ventnor or the Company)
conducted the following activities, which are summarised here:
Exploration
In October, Ventnor announced a new silica sand project at Arrowsmith which is situated 270km north
of Perth, WA. Silica sand is used in glass manufacturing, concrete construction and as a tech metal.
Ventnor advised that Arrowsmith has the potential for a significant silica sand resource that could supply
what is a dwindling sand supply in the Asia-Pacific region
Recently Asian regional governments have declared sand as a strategic resource due to the supply
deficits. Social pressure has been mounting on the environmental damage caused by (often) illegal
mining activities such as river dredging. The increase in coastal developments has also reduced access
to resources.
This market has been investigated in previous years but it is the looming shortage of product which has
caused increasing prices, making Australian prospects more competitive - despite the additional
distance and shipping costs.
With this change in the market dynamics the Company investigated prospective sites which had some
prior exploration indicating suitable sand - along with an important logistics solution - proximity to either
a port or connecting rail. Certain areas along the under-utilised Eneabba-Geraldton rail line were more
closely examined and EL applications were made for ground intersected by the rail line providing direct
access to the ship-loading facilities at the Geraldton Port - facilitating a unique logistics solution.
The combined EL applications in the Arrowsmith project area predominantly cover Vacant Crown Land
with little freehold land, and are extensively covered by cleared tracks from historic oil exploration
seismic surveys and exploration for heavy mineral sand – with the latter indicating potential for significant
sand resources. The area is easily accessed by the adjacent Brand Highway.
Investigations in to the potential market were extensive, wide ranging and time consuming, resulting in
a comprehensive collation of market data. Demand for sand in current burgeoning infrastructureconstruction programs utilising concrete in Asia - particularly China, India and Vietnam - has put
pressure on suppliers and consequently, on prices. Contact has been established with the two largest
importers of construction sand in to Singapore and samples forwarded for their test work.
Ventnor Resources Limited
2
DIRECTORS’ REPORT
Asian demand is increasing for energy-saving double glazing and for applications within the expanding
automobile industry in China and India. Demand is also increasing for high purity silica sand in the
production of Photo Voltaic panels and Silicon-Metal composite material for high capacity Lithium-ion
rechargeable batteries.
Preliminary reconnaissance work on the Arrowsmith Project indicates substantial potential for sand
resources suitable for both glass making and construction which could address the requirements of the
Asia-Pacific region.
The area potentially has low environmental impact mining propositions and the rehabilitation techniques
are well established in the industry.
Preliminary assays and testwork indicate that processing to upgrade the silica to glass- making quality
will have a low capital intensity, low technical risk and requiring no chemicals.
SILICA SAND
MARKET DYNAMICS
1. Globally, silica sand is a strong growth mineral due to the demand by the construction sector,
wherein its use in the manufacture of flat glass for windows is constant. Greater growth is being
felt in the Asian market, particularly China where there is a massive glass manufacturing
expansion.
2. There’s increased demand for specialised plate glass required in double glazing created by
Asian/Pacific governments in efforts to reduce energy demands.
3. Developing Asian markets have increasing demand for glass in their developing automobile
industry.
4. New markets address increasing demand for silica sand as a “tech metal” for use in production
of Photo Voltaic panels and Silicon-Metal composite material for high capacity Lithium-ion
rechargeable batteries.
5. Rationalisation of major producers of silica sand has resulted in a relatively small number of
sand-producing corporations.
6. The market for silica sand in the Asia/Pacific region is forecast to advance 6.1% per year to 138
million metric tons in 2018.
7. Silica sand demand by region is shown in table below:
Region
% of Global demand
Asia-Pacific
47%
North America
20%
Western Europe
16%
Eastern Europe
8%
Africa/Middle East
5%
Central and South America
4%
Ventnor Resources Limited
3
DIRECTORS’ REPORT
SILICA SAND USES
Introduction
Quartz is the most common silica crystal and the second most common mineral on the earth's surface.
It is found in almost every type of rock: igneous, metamorphic, and sedimentary. While quartz deposits
are abundant, and quartz is present in some form in nearly all mining operations, high purity and
commercially viable deposits occur less frequently. Silica sand deposits are most commonly surfacemined in open pit operations, but dredging and underground mining methods are also employed.
Silica sand has supported human progress throughout history, being a key raw material in the industrial
development of the world, especially in the glass, metal casting, and ceramics industries. Silica
contributes to today's information technology revolution, being used in computer components, providing
raw materials for silicon chips and as quartz for PV panels.
Glassmaking
Silica sand is the primary component of all types of standard and specialty glass. It provides the
essential SiO2 component of glass formulation; its chemical purity is the primary determinant of colour,
clarity and strength in glass. Industrial sand is used to produce flat glass for building and automotive
use, container glass for foods and beverages, and tableware.
Metal Casting
Industrial sand is an essential part of both the ferrous and non-ferrous foundry industries. Metal parts
ranging from engine blocks to sink faucets are cast in a sand-and-clay mould to produce their external
shape, using a resin-bonded core to create the desired internal shape. Silica’s high fusion point
(1,760°C) and low rate of thermal expansion produce stable cores and moulds compatible with all
pouring temperatures.
Metallurgical Uses
In metal production, silica sand operates as a flux to lower the melting point and viscosity of slag to
make it more reactive and efficient. Lump silica is used either alone or in conjunction with lime to achieve
the desired base/acid ratio required for final purification of metals.
Chemical Production
Silicon-based chemicals are found in thousands of everyday applications ranging from food processing
to soap and dye production. These chemicals are used in products such as household and industrial
cleaners, in the manufacture of fibre optics, and to remove impurities from cooking oil and brewed
beverages.
Paint and Coatings
Paint formulators select micron-sized industrial sands to improve the appearance and durability of
architectural and industrial paints and coatings. High purity silica produces critical performance
properties such as brightness reflectance and colour consistency.
Ceramics
Ground silica is an essential component of the glaze and body formulations of all types of ceramic
products, including tableware, sanitary ware and floor and wall tile. In the ceramic body, silica is the
skeletal structure onto which clays and flux components attach. Silica products are also used as the
primary aggregate to provide high-temperature resistance to acidic attack in industrial furnaces.
Filtration and Water Production
Industrial sand is used to filter water to become drinkable. Uniform grain shapes and grain size
distributions produce efficient filtration bed operations for the removal of contaminants from wastewater
to provide potable water. As silica is chemically inert, it will not degrade or react when it comes in
contact with acids, contaminants, volatile organics, or solvents.
Oil and Gas Recovery
Known commonly as proppant, or “frac sand,” industrial sand is pumped down holes in deep well
applications to prop open rock fissures to increase the flow rate of natural gas or oil. In this specialised
application, round whole-grain sand is used to maximise permeability and to prevent formation cuttings
from entering the well bore.
Ventnor Resources Limited
4
DIRECTORS’ REPORT
CONSTRUCTION SAND
Construction sand is the primary structural component in a wide variety of building and construction
products. Whole-grain silica is used in flooring compounds, mortars, specialty cements, stucco, roofing
shingles, skid-resistant surfaces, and asphalt mixtures to provide packing density and flexural strength
without adversely affecting the chemical properties of the binding system. Ground silica performs as a
functional extender to add durability, anti-corrosion and weathering properties in epoxy-based
compounds, sealants and caulks.
ASIAN MARKETS
SINGAPORE
Singapore building construction uses one million tonnes of concrete a month, which includes 300,000
tonnes of construction sand. Current sources are Malaysia, Cambodia, Myanmar and occasionally
Philippines. Other regional sources have placed restrictions on or have totally banned exports of their
local sand. Sources are generally dredged from rivers with consequential unacceptable environmental
impacts. The Singapore Building and Construction Authority (BCA) has placed a requirement that 5%
of construction sand be imported from “non-traditional” sources which includes Australia. Singapore is
concerned that current sources may become unreliable or intermittent and is actively encouraging a
greater spread of sources. Importers are concerned that the BCA will raise that requirement to 10% from
non-traditional sources, as originally intended. If Singapore continues at its current rate of growth, this
could be a significant market for Australian suppliers.
INDIA
The building expansion program underway has put incredible pressure on sand suppliers for concrete,
so much so that illegal dredging of rivers has resulted in recent public scrutiny of the environmental longterm impacts. This is also potentially a significant market for construction sand.
VIETNAM
Vietnam has gone from an exporter of industrial sand, to an importer, with increased use in concrete
with a significant building boom underway.
Ventnor management believes that the Arrowsmith Project has the potential for significant silica
sand resources to supply increasing markets in the Asia-Pacific region for both glass making
and construction and increasingly the Tech metal market.
Ventnor Resources Limited
5
DIRECTORS’ REPORT
Arrowsmith Project Details
Ventnor Resources has applied for three exploration licenses north of Eneabba, Western Australia, to
explore for construction sand and high-quality silica sand. The details of these tenements, known
collectively as the Arrowsmith Project, are shown below in Table 1, with the location in Figure 1.
Tenement
Holders
Application Date
Expected Grant
Date
Area
(Km2)
ELA70/4986
Ventnor Mining Pty Ltd
25/05/2017
Late Q2 2018
93
ELA70/4987
Ventnor Mining Pty Ltd
25/05/2017
Late Q2 2018
86
ELA70/5027
Ventnor Mining Pty Ltd
29/08/2017
Late Q2 2018
179
Table 1 – Arrowsmith Tenement Details
Figure 1 – Arrowsmith Project Location
Ventnor Resources Limited
6
DIRECTORS’ REPORT
The targeted silica sand deposits are the aeolian sand dunes that overlie the Pleistocene limestones
and paleo-coastline which host the Eneabba heavy mineral deposits.
The Exploration Targets for the Arrowsmith Project are:
Arrowsmith North – 100 Million to 140 Million tonnes high-quality silica sand;
Arrowsmith South – 40 Million to 80 Million tonnes high-quality silica sand.
The potential quality and grade of these Exploration Targets are conceptual in nature. There has
been insufficient exploration to estimate a Mineral Resource; it is uncertain if further exploration
will result in the estimation of a Mineral Resource.
The image (Figure 2) below is a topographic map of the area generated by Shuttle Radar Topography
Mission data (SRTM). This map was used to identify potential dune structures as topographic highs,
which have been followed by ground field investigation and sampling using a hand-held auger.
Arrowsmith North
dune system
Arrowsmith Central
limestone
35 kilometres
Arrowsmith South
dune system
Figure 2 Arrowsmith Project SRTM topography
Ventnor Resources Limited
7
DIRECTORS’ REPORT
The image (Figure 3) below is a schematic section showing the silica sand dune that is targeted for
exploration. The targeted dune is the area above the surrounding natural surface and well above the
standing water table.
Pleistocene limestone
Figure 3 Schematic section of Silica Sand Dune Exploration Target
Three areas were investigated: Arrowsmith North for construction sand which may also be upgraded to
glass quality; Arrowsmith Central, which is prospective for silica sand and also limestone; and
Arrowsmith South, prospective for high quality silica sand.
Initial samples were taken by hand auger and selected from below the humus layer, typically the first
30cm. Samples were sent to Intertek Laboratory in Perth for silica sand analysis via a Four-Acid digest
and ICP finish. The table below shows the major constituents of the sand, with full analytical results
available in the Appendix.
Ventnor Resources Limited
8
DIRECTORS’ REPORT
MGA_East MGA_North
Location
Zone50
Zone50
Arrowsmith North
6729258
317330
6730256
Arrowsmith North
317160
6731249
Arrowsmith North
316989
6732242
Arrowsmith North
316818
316642
6733263
Arrowsmith North
6735123
Arrowsmith North
316319
Arrowsmith North
316115
6736295
316109
6737182
Arrowsmith North
316584
6737185
Arrowsmith North
Arrowsmith North
316974
6737193
Arrowsmith North
6737207
317964
6731628
Arrowsmith North
321170
Arrowsmith North
319751
6731161
6721353 Arrowsmith Central
318790
318383
6721357 Arrowsmith Central
6722076 Arrowsmith Central
317956
316750
6722030 Arrowsmith Central
315686
6725167 Arrowsmith Central
6718805 Arrowsmith Central
323890
322516
6718792 Arrowsmith Central
Arrowsmith South
321399
6712070
6711127
Arrowsmith South
321141
6710201
Arrowsmith South
321295
321715
6707710
Arrowsmith South
6705357
Arrowsmith South
322815
323118
6704616
Arrowsmith South
Arrowsmith South
323047
6702748
6705732
Arrowsmith South
318284
319519
6705047
Arrowsmith South
318284
6705732
Arrowsmith South
319519
6705047
Arrowsmith South
SiO2
%
98.40
97.80
98.00
96.80
97.30
97.90
98.40
98.20
96.10
99.10
99.00
99.30
98.50
95.00
94.90
95.70
95.50
97.30
99.30
98.30
94.90
96.10
97.70
98.30
97.40
97.10
96.60
93.30
95.90
97.60
98.30
Al2O3
ppm
6,979
10,547
9,448
15,988
12,801
9,826
7,389
8,611
7,538
3,733
3,684
2,653
6,527
25,477
25,529
21,472
21,314
13,323
2,898
7,907
26,338
18,871
10,848
8,371
11,735
13,528
17,069
35,969
20,165
11,079
6,955
Fe2O3
%
0.19
0.36
0.30
0.55
0.48
0.36
0.26
0.29
0.19
0.10
0.14
0.12
0.24
0.58
0.59
0.44
0.42
0.26
0.09
0.17
0.55
0.43
0.12
0.08
0.34
0.40
0.31
0.61
0.40
0.16
0.14
K2O
ppm
1,885
993
800
1,629
983
881
588
891
3,997
891
411
213
269
5,847
6,663
7,531
7,649
2,121
677
2,326
7,923
5,220
5,318
4,554
2,464
2,521
2,934
10,230
7,256
6,018
2,338
TiO2
ppm
1,621
1,155
1,243
1,636
1,397
1,513
1,102
1,320
1,264
874
1,277
1,044
1,092
1,737
2,376
2,079
1,988
1,360
1,246
1,268
1,880
1,688
1,611
1,562
2,693
3,146
3,257
2,329
1,784
2,241
2,313
LOI-1000C
%
0.33
0.53
0.48
0.69
0.63
0.52
0.40
0.40
1.13
0.23
0.31
0.21
0.40
0.98
0.92
0.66
0.83
0.63
0.15
0.28
0.83
0.82
0.30
0.18
0.52
0.49
0.69
1.04
0.61
0.21
0.39
High grade silica sand is sand which has purity greater than 99.5% SiO2. It typically will require
processing to remove the various deleterious minerals to achieve the highest possible silica grade.
Auger samples were composited into two samples representing “Cream” and “Yellow” sand and supplied
to Nagrom Laboratory in Perth to determine the Size by Analysis.
This technique analyses the elemental chemistry of a suite of particle sizes to determine where the
deleterious minerals report to; below is a summary of the results. The results indicate that +90% of the
dune sand is sized between +0.212mm and -1mm, preferentially retains the silica sand grains while
eliminating many of the impurities.
Preliminary indications are encouraging in that the dune sand located on the Arrowsmith tenements can
be upgraded by conventional techniques, to provide a high-grade purity of 99.5% SiO2 with only nominal
amounts of benign deleterious minerals.
Ventnor Resources Limited
9
DIRECTORS’ REPORT
Size by Analysis
SAMPLE
Mass
%
SiO2 LOI1000 Fe2O3 Al2O3
%
%
%
%
98.757
0.22
0.145
0.334
Arrowsmith North Cream Sand
Assay Head
TiO2
CeO2
0.104
3.0
%
ppm
Arrowsmith North Cream Sand Size by Analysis
Size (mm)
+1
0.16% 96.054
0.57
2.761
0.335
0.043
<1
+0.5
41.86% 99.319
0.06
0.348
0.181
0.041
<1
+0.355
24.88% 98.918
0.01
0.625
0.220
0.048
<1
+0.212
26.20% 99.047
0.06
0.486
0.272
0.060
<1
+0.106
5.36% 96.879
0.02
1.717
0.566
0.527
3
+0.075
0.43% 91.143
0.16
3.829
1.481
2.057
65
+0.045
0.45% 90.356
0.31
4.127
2.102
1.225
58
+0.038
0.10% 89.604
0.68
4.198
2.557
1.015
50
-0.038
0.55% 81.893
5.03
3.484
5.676
1.303
68
+0.212 - 1mm 92.94% 99.135
0.05
0.461
0.217
0.048
<1
0.328
0.870
0.134
8.0
Arrowsmith North Yellow Sand
Assay Head
97.780
0.44
Arrowsmith North Yellow Sand Size by Analysis
Size (mm)
+1
0.67% 96.971
0.09
2.459
0.479
0.063
4
+0.5
60.51% 98.995
0.11
0.425
0.369
0.050
2
+0.355
20.62% 98.709
0.10
0.519
0.404
0.064
2
+0.212
10.98% 98.378
0.09
0.758
0.526
0.087
2
+0.106
3.57% 95.624
0.19
1.511
1.225
0.774
12
+0.075
0.78% 88.111
0.10
4.241
3.257
1.957
96
+0.045
0.34% 89.209
0.57
3.408
3.031
1.341
103
+0.038
0.29% 89.694
0.60
3.088
3.303
1.014
67
-0.038
2.23% 58.879
9.97
7.225 20.339
1.575
197
+0.212 - 1mm 92.11% 98.857
0.11
0.486
0.058
2
0.396
Size by Analysis for composited auger samples
Ventnor Resources Limited
10
DIRECTORS’ REPORT
EXPLORATION TARGETS
Exploration Targets for potential high-grade silica sand have been generated for two areas within the
Arrowsmith Project: Arrowsmith North and Arrowsmith South, see below:
Arrowsmith North
Arrowsmith North Exploration Target
The Arrowsmith North Exploration Target area focuses on a prominent broad dune structure, (see
above), and avoids existing infrastructure and potential conservation areas. The potential volume is
estimated from the 40mRL (surrounding RL) to the top of the dune and assumes that between 70% and
100% of the dune is silica sand suitable for processing. The estimate uses an in-situ bulk density of
1.5t/m3 to calculate the tonnage. The area has the potential to be a significant tonnage of construction
sand adjacent to the Eneabba-Geraldton rail line with direct access to the Geraldton Port. The target
grade of +95% SiO2 is considered conservative as all samples, except two, taken from the area exceed
this value; processing is expected to increase this grade.
Ventnor Resources Limited
11
DIRECTORS’ REPORT
Arrowsmith South
The Arrowsmith South Exploration Target focuses on the southern end of a topographical high that is
noted as containing an intercalation of limestone and dune sands (see below), and avoids existing
infrastructure and potential conservation areas. The potential volume is estimated from the 45mRL to
the top of the dune and assumes that between 50% and 100% of the dune is silica sand for processing.
The estimate uses an in-situ bulk density of 1.5t/m3 to calculate the tonnage. The target grade of +95%
SiO2 is considered conservative as assays from all samples taken from the area exceed this value;
processing is expected to increase this grade.
Arrowsmith South Exploration Target
The initial metallurgical testwork indicates that the in-situ sand can be beneficiated to produce a high
SiO2 silica sand product, suitable for commercial sale.
Ventnor Resources Limited
12
DIRECTORS’ REPORT
Future Work
Mineralogical analysis is currently underway to determine the deleterious minerals that remain in the
+0.212mm and -1mm size fraction. Dependent on this determination, testwork will determine the best
methodology to remove these minerals from the silica sand grains.
A deeper hand-auger program will be undertaken in the next few months to better determine the
variability of the sand quality through the dune system.
An aircore drilling program is proposed to determine the extent of the dune system and the variability of
the grade, to be undertaken after the granting of the tenements.
Bulk samples will be collected to undertake further metallurgical testwork and determine the most
suitable processing circuit.
Exploration Events Subsequent to the Half-Year
On 2 January 2018 Ventnor made application for a further tenement, ELA70/5109 in the Arrowsmith
area. This tenement application is congruent with existing tenement applications in the Arrowsmith
project area and will further enhance the project’ access to the existing Eneabba-Geraldton rail to the
Geraldton port.
On 30 January 2018 Ventnor announced some results on the Arrowsmith samples collected during
December 2017 when the Company conducted a mapping and shallow hand auger program to collect
composite representative samples from the Arrowsmith North prospect.
Samples were submitted to Nagrom Laboratories for an initial testwork program, which would emulate
conventional sand processing techniques.
This testwork confirms that processing to upgrade the sand to glass-making quality will have a lowcapital intensity, low technical risk and requires no processing chemicals.
Further testwork programs will be undertaken to investigate processing options to higher quality and
higher value products.
Also announced were preliminary testwork results, which indicated the bulk sand could be upgraded
using simple sizing techniques, with further testwork to be carried out to determine if the sand could be
further upgraded. In addition to this, samples were to be prepared and sent for proppant testing to API
RP-19C standards.
At the time of this announcement not all of the results of the auger sampling completed in December
were available because of Laboratory delays. These results and the proppant testing results were still
outstanding at the time of this report.
However, the results of silica sand testwork that have been received are summarised below.
Ventnor Resources Limited
13
DIRECTORS’ REPORT
A 5kg composite from Arrowsmith North was tested at the Nagrom Laboratory in Kelmscott, in Perth,
using the following flowchart:
Nagrom Silica Sand Testwork
Head assay Arrowsmith Nth Composite
~5kg
plus mass balance throughout
Dry Bulk Density
Attrition 25-30%
10 Mins
Assay
Assay
Assay
Assay both mag and non-mag
Assay
Assay
Seive Separation
<0.212mm
0.212mm - 1.18mm
+1.18mm
Magnetic Separation of
Product @ 14,000 gauss
Product
Non-mag is Product
Seive Separation Non-mag
Product (0.85mm-0.425mm)
Product (0.425-0.212mm)
On the page following is a table detailing the testwork results. The feed stock in the test had a head
assay of 97.7% SiO2 +LOI1000C, after attritioning, magnetic separation and sizing, the 0.425mm - 0.85mm
product achieved a grade of 99.5% SiO2 +LOI1000C. The remainder of the product, 0.212mm - 0.425mm,
returned an assay of 99.3% SiO2 +LOI1000C. It is believed that additional testwork will improve both of
these product grades.
Of significance is the mass balance achieved during testing, as this is an indication of the potential
recovery from the in-situ resources. From the feed stock, 93.6% is recovered in the initial 0.12mm –
1.18mm sizing and passed on for attritioning and magnetic separation. With negligible mass loss in the
magnetic separation and final sizing step, the potential product recovery is +93%. The higher grade
0.425mm - 0.85mm sizing constitutes 70% of the final product with the finer 0.212mm - 0.425mm, sizing
making up the balance.
Ventnor Resources Limited
14
DIRECTORS’ REPORT
Ventnor Resources Limited
15
DIRECTORS’ REPORT
In addition to the testwork completed by Nagrom, Scanning Electron Microscopy (SEM) and Qualitative
X-ray Diffraction (XRD) work has been completed by Microanalysis in East Perth to better understand
the mineral forms of the deleterious elements. An understanding of the minerals that are present in the
bulk sand mass will aid in further upgrading of the final product.
This work has resulted in the following findings:
•
The Loss on Ignition (LOI1000C) is largely because the presence of salts such as Halite and
Sylvite;
•
The Fe and Ti minerals are present as Iron oxides, Ilmenite and Rutile;
•
Aluminium, a major contaminant, is present as Al(OH)3, being a form of bauxite such as
Gibbsite; and
•
Mineral grains are largely liberated, with 60-78% for the Fe and Ti minerals, and 99.8% for the
Gibbsite.
Future Testwork
The next phase of planned testwork focused on the removal of the dense Fe/Ti minerals, >4g/cc, and
the lighter Gibbsite, <2.4g/cc, in comparison with the quartz sand grains, 2.62g/cc. Initial testing using
Heavy Liquid Separation (HLS) will be followed with a bulk sample, ~200kg, to be tested over a wet
table to determine if conventional gravity separation equipment such as spirals will assist with the final
product upgrade. Testwork to date shows that ~5,000ppm, or 0.5% of the current product, is reporting
to these minerals. Successful gravity separation could upgrade the final product to >99.8% SiO2
+LOI1000C.
It is anticipated the bulk sample product will be used for marketing purposes to secure offtake and pricing
agreements.
Competent Person’s Statement
The information in this release that relates to Exploration Results and Exploration Targets is based on,
and fairly represents, information compiled by Mr David Reid who is a Member of the Australian Institute
of Geoscientists (MAIG). Mr Reid is a contractor to Ventnor Resources Limited. Mr Reid has sufficient
experience which is relevant to the style of mineralisation and type of deposit under consideration and
to the activity which he is undertaking to qualify as a Competent Person as defined in the “2012 Edition
of the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves.”
Mr Reid consents to the inclusion in this report of the matters based on information provided by him and
in the form and context in which it appears.
Corporate
Demerger of Delgare Pty Ltd
During the period Ventnor held its Annual General Meeting on 30 November 2017 at which shareholders
approved the demerger of Delgare Pty Ltd with an in-specie distribution of Delgare shares to Ventnor
shareholders as at the nominated record date.
Delgare Pty Ltd was a wholly owned subsidiary of Ventnor which held the Thaduna/Green Dragon
Copper Project (TGD) in the Murchison district of Western Australia. The Project is located 40km east
of DeGrussa and represents the largest copper resource in the Doolgunna-Bryah Basin Region outside
of Sandfire’s DeGrussa Doolgunna Project.
Ventnor Resources Limited
16
DIRECTORS’ REPORT
Following the successful exploration of TGD by Ventnor and the identification of a 142,000 tonne in situ
copper resources there were a series of dealings with Sandfire Resources NL on the project. These
were fully covered in the Notice of Meeting document and will not be repeated as the outcome is that
the sole asset of Delgare is a royalty on copper production from the Project (Royalty) which can be
summarised as:
“The consideration for the purchase comprised the issue of Sandfire shares to Delgare or its nominee
to a value of $1,700,000, a deferred cash payment of $950,000 if Sandfire proceeds with a decision to
mine from the Project (DTM Payment) and a royalty on copper production from the Project (Royalty).”
The initial share consideration has been paid and the DTM Payment and Royalty remains. A short
summary of the terms and conditions of the Royalty follows:
“For each calend
Share your feedback
Discover